Dear readers,
Luminol (C8H7N3O2) is a chemical that exhibits chemiluminescence. This compound can be easily made with 3 chemicals that are present in a typical chemist’s laboratory – 3-nitrophthalic acid, hydrazine and sodium dithionite. However, today I’m going to show you another method of doing it, using chemicals that can be found at your neighbourhood minimart!
Materials:
Hot plate (used to heat stuff up)
Heat gun
Water
Vinyl / PVC gloves (make sure it says vinyl or PVC)
Isopropyl alcohol (rubbing alcohol)
Sodium hydroxide (solid drain cleaner)
Hydrochloric acid (liquid drain cleaner)
Sulfuric acid (liquid drain cleaner)
Sodium nitrate (made in http://www.youtube.com/watch?v=hQJhf_24-QM)
Hydrazine sulfate (made in http://www.youtube.com/watch?v=UB7vwIFCnR0)
Sodium acetate trihydrate (made in http://www.youtube.com/watch?v=Yxk3OZWq9Ls)
Polyethylene glycol (brake fluid that has a boiling point higher than 230 degrees Celsius)
Sodium metabisulfite (used by home brewers to sterilise winemaking and beermaking mixtures)
Aluminium foil
Sodium bisulfate (pH-lowering chemical for swimming pools)
Acetone (nail polish remover or cleaning agent)
Method:
(The process is pretty complicated and dangerous at parts and so should only performed by, or under the direct supervision of an experienced chemist.)
First we obtain diethylhexyl phthalate by refluxing 50g of finely cut vinyl gloves in enough isopropyl alcohol to completely cover them for at least one hour, preferably three to four.
The alcohol solution of diethylhexyl phthalate is filtered and the supernatant is boiled until it reduces to half its volume. An equal amount of water along with 10g of sodium hydroxide is added and the mixture is boiled for an hour. This causes the diethylhexyl phthalate to hydrolyse into phthalic acid and 2-ethylhexanol. After the solution cools it will phase separate into an aqueous layer containing disodium phthalate (below) and an organic layer containing the alcohols (top).
Retaining just the aqueous layer, 25ml of 12M (12 molar, which is very concentrated) hydrochloric acid is added to precipitate the phthalic acid (which has low solubility in cold environments) after cooling in the fridge or an ice bath. The supernatant is discarded and the residue of the phthalic acid is purified and converted into phthalic anhydride by heating it to 300 degrees Celsius on a hot plate. First the water boils off and then the phthalic anhydride evaporates and condenses on the sides of the beaker. At this point, a flask of cold water is placed over the beaker to allow the phthalic anhydride to deposit on it. Periodically the phthalic anhydride deposits are removed until no more can be obtained.
45ml of sulfuric acid along with 13g of phthalic anhydride and 19g of sodium nitrate are stirred together with the temperature slowly ramped up to 110 degrees Celsius. Once the temperature is reached, the reaction is held for another one hour to nitrate the phthalic anhydride to 3-nitrophthalic anhydride. Heating is then removed and the mixture is allowed to cool back to room temperature. The gelled mixture is then transferred into 150ml of cold water and vigorously stirred until all the flakes are broken up and brown nitrogen dioxide gas is no longer produced. Then, the mixture is allowed to settle overnight. After that, this is vacuum filtered and washed with two 50ml portions of water and allowed to dry under the forced air stream.
1g of the 3-nitrophthalic acid is combined with 616mg hydrazine sulfate and 1.4g sodium acetate trihydrate and 1ml of water. The mixture is boiled with a heat gun until dry. Then 4ml of polyethylene glycol is added. The mixture is heated to 230 degrees Celsius for ten minutes.
The mixture is allowed to cool to below 80 degrees Celsius and then transferred into a large beaker with 100ml of water. 10g sodium hydroxide and 13g sodium metabisulfite are dissolved into the mixture. 5g of torn aluminium foil is then jammed into the beaker and held down with a conical flask while a round-bottomed flask of cold water is placed on top. Vigorous hydrogen evolution and self-heating will occur as the aluminium foil reacts. The mixture is allowed to reflux until it stops on its own. Additional aluminium foil is added and the process repeated until the mixture has no further change in colour.
The mixture is filtered and the residue washed with an additional 50ml of water. The filtrate is then separated from any floating organic products. In a separate container a solution of 200ml of water and 25g of sodium bisulfate is prepared. 100ml of acetone is added and the filtrate is directly added to the mixture with vigorous stirring. Stirring is continued until there is no further change in the consistency or volume of the slurry. The supernatant is decanted off and allowed to evaporate.
The cake of luminol is mixed with 100ml of water and thoroughly washed to remove any remaining salts. The mixture is vacuum filtered and allowed to dry.
The luminol can be tested by reacting an alkaline solution of it with bleach.
Procedure from: http://www.youtube.com/watch?v=58Ve69s0qD0
Reaction by GITS
